Showing 20 products
-
FSI B21
FSI 21 - 8 stk87 cmMaks 2,4 cm30 cm25 cm11-14 hkBenzinNej68 cm125 kg- Hill hold system (Pat. pending) – unique system developed by FSI to increase safety and give full control when moving on ramps, up steps or in terrain.
- Closed bearing housing – no daily maintenance is required as the cutter wheel bearing is pre-greased from factory for more than 1000 hours of normal operation.
- Turntable design – a well-balanced pivot point and two individual wheel brakes makes cutting easy on the operator
- Improve ergonomics – position the vibration reduced operator handle as you prefer with many adjustment options
- Safety bar – disengaging the cutter wheel upon release
- V-belt drive for optimal power transmission
- Easily accessible lashing and lifting points
- Centrifugal clutch
- Manual brake for each wheel
- Large and easy-to-operate wheels
- Tool set
-
FSI B22
FSI 21 - 8 Stck90 cmMax 2,4 cm je Schwenk30 cm25 cm14 PSBenzinNein68 cm210 kg- Large wheels with individual oil motors (2WD)
- Vibration reduced and height-adjustable handlebar
- Safety bar, disengaging the cutter wheel upon release
- Manual sweep across pivot joint
- Manual brake for each wheel
- Bypass valve to disengage drive for freewheeling
- Electromagnetic clutch
- V-belt drive for optimal power transmission
- Braking of cutter disc on disengaging
- Electrical start of engine
- Easily accessible lashing & lifting points
- Tool set
-
FSI B28
FSI 21 - 8 Stck135 cmMax 4,8 cm je Schwenk80 cm38 cm26,5 PSBenzinNein80 cm665 kg- V-belt drive for optimal power transmission
- FSI power-clutch – powerful hydraulic clutch with active brake
- Safety bar, disengaging the cutter wheel upon release
- Fast braking of cutter disc on disengaging
- Hydraulic 2WD
- Mechanical differential lock for better mobility and increased traction
- 90 degrees swivel control panel, provides excellent visibility of the cutting area
- Easily accessible lashing & lifting points
- Tool set
- Integrated toolbox
- OPTION: Twin wheels with centre bolt for easy fitting/removing
- OPTION: FSI power-sweep – intelligent sweep controller for top performance
-
FSI B31
FSI 25 - 8 Stück120 cm Max 3,6 cm je Schwenk68 cm 40 cm26.5 psBenzinNein74 cm650 kg- Keine tägliche Wartung und der Wegfall von Keilriemen senken die Betriebskosten und die Werkstattzeiten.
- Gute Manövrierfähigkeit und Stabilität durch gegenläufige Raupen und einen niedrigen Gewichtsschwerpunkt.
- Vollständige Steuerung des Betriebs über das ausschwenkbare Bedienpult.
- Sicherheitsbügel, der das Schneidrad beim Loslassen auskuppelt, um die Sicherheit des Bedieners zu erhöhen.
- Leicht zugängliche Zurr- und Hebepunkte für einen schnellen und sicheren Transport.
-
FSI B38
FSI 25 - 12 Stck170 cmMax 5,7 cm je Schwenk85 cm44 cm38 PSBenzinNein79 - 127 cm840 kg- V-belt drive for optimal power transmission
- FSI power-clutch – powerful hydraulic clutch with active brake
- FSI power-sweep – intelligent sweep controller for top performance
- FSI power-cut – optimised cutting disc
- Maintenance-free bearing housing at cutting head
- Fast braking of cutter disc on disengaging
- Flex chip guard for optimal chip collection
- LED work light
- Easily accessible lashing & lifting points
- Tool set
- Integrated toolbox
-
FSI B38 4WD
FSI 25 - 12 Stck170 cmMax 5,7 cm je Schwenk85 cm44 cm38 PSBenzinNein79 - 127 cm900 kg- V-belt drive for optimal power transmission
- FSI power-clutch – powerful hydraulic clutch with active brake
- FSI power-sweep – intelligent sweep controller for top performance
- FSI power-cut – optimised cutting disc
- Maintenance-free bearing housing at cutting head
- Fast braking of cutter disc on disengaging
- Flex chip guard for optimal chip collection
- LED work light
- Easily accessible lashing & lifting points
- Tool set
- Integrated toolbox
-
FSI B38 4WD REMOTE
FSI 25 - 12 Stck170 cmMax 5,7 cm je Schwenk85 cm44 cm38 PSBenzinJa, Scanreco79 - 127 cm900 kg- V-belt drive for optimal power transmission
- FSI power-clutch – powerful hydraulic clutch with active brake
- FSI power-sweep – intelligent sweep controller for top performance
- FSI power-cut – optimised cutting disc
- Maintenance-free bearing housing at cutting head
- Fast braking of cutter disc on disengaging
- Flex chip guard for optimal chip collection
- LED work light
- Easily accessible lashing & lifting points
- Tool set
- Integrated toolbox
-
FSI B38 TRACK
FSI 25 - 12 Stck170 cmMax 5,7 cm je Schwenk85 cm44 cm38 PSBenzinJa, Scanreco78 - 115 cm1100 kg- V-belt drive for optimal power transmission
- FSI power-clutch – powerful hydraulic clutch with active brake
- FSI power-sweep – intelligent sweep controller for top performance
- FSI power-cut – optimised cutting disc
- Maintenance-free bearing housing at cutting head
- Fast braking of cutter disc on disengaging
- Flex chip guard for optimal chip collection
- LED work light
- Easily accessible lashing & lifting points
- Tool set
- Integrated toolbox
-
FSI D30
FSI 25 - 8 Stck135 cmMax 5,2 cm je Schwenk80 cm38 cm25 PSDieselNein80 - 135 cm810 kg- V-belt drive for optimal power transmission
- FSI power-clutch – powerful hydraulic clutch with active brake
- Fast braking of cutter disc on disengaging
- LED work light
- Easily accessible lashing & lifting points
- Tool set
- Integrated toolbox
- OPTION: FSI power-sweep – intelligent sweep controller for top performance
-
FSI D30 TRACK
FSI 25 - 8 Stck135 cmMax 5,2 cm je Schwenk80 cm38 cm25 PSDieselNein80 - 115 cm970 kg- V-belt drive for optimal power transmission
- FSI power-clutch – powerful hydraulic clutch with active brake
- Fast braking of cutter disc on disengaging
- LED work light
- Easily accessible lashing & lifting points
- Tool set
- Integrated toolbox
- OPTION: FSI power-sweep – intelligent sweep controller for top performance
-
FSI D30 TRACK REMOTE
FSI 25 - 8 Stck135 cmMax 5,2 cm je Schwenk80 cm38 cm25 PSDieselJa, Scanreco80 - 115 cm970 kg- V-belt drive for optimal power transmission
- FSI power-clutch – powerful hydraulic clutch with active brake
- Fast braking of cutter disc on disengaging
- LED work light
- Easily accessible lashing & lifting points
- Tool set
- Integrated toolbox
- OPTION: FSI power-sweep – intelligent sweep controller for top performance
-
FSI D60
FSI 25 - 16 Stck170 cmMax 6,8 cm je Schwenk85 cm44 cm60 PSDieselJa, Scanreco80 - 123 cm1250 kg- Fast braking of cutter disc on disengaging
- Gear and V-belt drive for optimal power transmission
- Hydraulically controlled mechanical clutch
- Maintenance-free bearing housing at cutting head
- FSI power-sweep – intelligent sweep controller for top performance
- FSI power-cut – optimised cutting disc
- Scanreco radio control with extra battery, battery charger and cable
- Lockable storage space for radio remote control
- LED work light
- Flex chip guard for optimal chip collection
- Lockable access to fuel- and hydraulic filling points
- Easily accessible lashing & lifting points
- Tool set
-
FSI D60 TRACK
FSI 25 - 16 Stck170 cmMax 6,8 cm je Schwenk85 cm44 cm60 PSDieselJa, Scanreco80 - 115 cm1450 kg- Fast braking of cutter disc on disengaging
- Gear and V-belt drive for optimal power transmission
- Hydraulically controlled mechanical clutch
- Maintenance-free bearing housing at cutting head
- FSI power-sweep – intelligent sweep controller for top performance
- FSI power-cut – optimised cutting disc
- Scanreco radio control with extra battery, battery charger and cable
- Lockable storage space for radio remote control
- LED work light
- Flex chip guard for optimal chip collection
- Lockable access to fuel- and hydraulic filling points
- Easily accessible lashing & lifting points
- Tool set
-
FSI D74
FSI 29 - 28 Stck200 cmMax 12,3 cm je Schwenk60 cm38 - 52 cm74 PSDieselJa, Scanreco89 - 152 cm1725 kg- T-Gear and double-sided V-belt drive for optimal power transmission
- Fast braking of cutter disc on disengaging
- Electrical controlled mechanical clutch with brake
- FSI power-sweep – intelligent sweep controller for top performance
- Scanreco radio control with extra battery, battery charger and cable
- 12V outlet for charging of remote controller battery
- Heavy-duty chip guard
- LED work light
- Easily accessible lashing & lifting points
- Tool set
-
FSI D74 TRACK
FSI 29 - 28 Stck200 cmMax 12,3 cm je Schwenk60 cm38 - 52 cm74 PSDieselJa, Scanreco89 - 140 cm1950 kg- T-Gear and double-sided V-belt drive for optimal power transmission
- Fast braking of cutter disc on disengaging
- Electrical controlled mechanical clutch with brake
- FSI power-sweep – intelligent sweep controller for top performance
- Scanreco radio control with extra battery, battery charger and cable
- 12V outlet for charging of remote controller battery
- Heavy-duty chip guard
- LED work light
- Easily accessible lashing & lifting points
- Tool set
-
FSI H20
FSI 21 - 12 StckMax 2,5 cm je Schwenk70 kg2,0 - 3,5 ton12-22 kW / 15-30 PS30-50 l/min @ max 250 barHydraulically driven stump cutter for fitting to an excavator or similar machine, where the machine itself is used to execute sweep and up/down
movement. Free choice of cutting direction. The cutting direction can easily be set at 45 degree intervals, in the joint between the unit and the fitting
plate for the tool attachment. The stump cutters are supplied with an uncoated top plate, on which an optional tool attachment can be fitted. We also
provide a selection of tool attachments. The stump cutters require a free-flow return to the tank (leak oil). -
FSI H20S
FSI 21 - 12 Stck70 cmMax 2,5 cm je Schwenk92 kg1,5 - 2,5 ton12-22 kW / 15-30 PS30-50 l/min @ max 250 barHydraulic driven stump cutter with integrated sweep movement for fitting to loaders and tool carriers. The stump cutter is supplied with an uncoated
backplate to which an attachment can be fitted. FSI provides a range of adaptor brackets suitable for the most common tool carriers and loaders upon
request.
Two hydraulic cylinders ensure a stable sweeping movement in either direction. Control of the sweeping movement can be done either from the tool
carrier or by an electronic control box depending on the connectors available on the tool carrier or loader.
FSI HxxS stump cutters require a free-flow return to the tank (leak oil). -
FSI H40
FSI 25 - 16 StckMax 5,2 cm je Schwenk150 kg3,0 - 7,0 ton18-31 kW / 25-42 PS50-75 l/min @ max 250 barHydraulically driven stump cutter for fitting to an excavator or similar machine, where the machine itself is used to execute sweep and up/down
movement. Free choice of cutting direction. The cutting direction can easily be set at 45 degree intervals, in the joint between the unit and the fitting
plate for the tool attachment. The stump cutters are supplied with an uncoated top plate, on which an optional tool attachment can be fitted. We also
provide a selection of tool attachments. The stump cutters require a free-flow return to the tank (leak oil). -
FSI H40S 50-75
FSI 25 - 16 Stck110 cmMax 5,2 cm je Schwenk200 kg???18-31 kW / 25-42 PS50-75 l/min @ max 250 barHydraulic driven stump cutter with integrated sweep movement for fitting to loaders and tool carriers. The stump cutter is supplied with an uncoated
backplate to which an attachment can be fitted. FSI provides a range of adaptor brackets suitable for the most common tool carriers and loaders upon
request.
Two hydraulic cylinders ensure a stable sweeping movement in either direction. Control of the sweeping movement can be done either from the tool
carrier or by an electronic control box depending on the connectors available on the tool carrier or loader.
FSI HxxS stump cutters require a free-flow return to the tank (leak oil). -
FSI H40S 80-110
FSI 25 - 16 Stck110 cmMax 5,2 cm je Schwenk250 kg???29-48 kW / 40-65 PS80-110 l/min @ max 250 barHydraulic driven stump cutter with integrated sweep movement for fitting to loaders and tool carriers. The stump cutter is supplied with an uncoated
backplate to which an attachment can be fitted. FSI provides a range of adaptor brackets suitable for the most common tool carriers and loaders upon
request.
Two hydraulic cylinders ensure a stable sweeping movement in either direction. Control of the sweeping movement can be done either from the tool
carrier or by an electronic control box depending on the connectors available on the tool carrier or loader.
FSI HxxS stump cutters require a free-flow return to the tank (leak oil).
FSI 21 - 8 stk
87 cm
Maks 2,4 cm
30 cm
25 cm
11-14 hk
Benzin
Nej
68 cm
125 kg
2,0 - 3,5 ton
30-50 l/min @ max 250 bar
1,5 - 2,5 ton
